Technology & Services

FCS-20G – High wear-resistant oil-impregnated sliding bearing material for heavy-load applications

FCS-20G – High wear-resistant oil-impregnated sliding bearing material for heavy-load applications

In motors and drive mechanisms, shaft bushings support the shaft and reduce friction during movement. Under conditions of low speed, oscillatory motion, or high loads, the oil film is difficult to maintain stably, increasing the risk of wear, scratching, and seizure between the shaft and the bushing.Peace-Lon's FCS-20G is an iron-based oil-impregnated sliding bearing material developed for these operating conditions. The material uses an iron matrix with a pearlitic structure and dispersed free graphite powder, thereby enhancing surface hardness, wear resistance, and lubricity.

What is FCS-20G?

FCS-20G is an Fe–C based oil-impregnated sliding bearing material. Through a special sintering method, the iron matrix structure is transformed from ferrite to pearlite. This change increases the surface hardness of the material, helping the bushing better resist wear under high load conditions. Additionally, free graphite powder with an average particle size of approximately 40 μm is dispersed within the material. Graphite aids lubrication at the contact surface, helping to reduce scratching and seizure when the oil film is not fully maintained.

Material Structure Improves Sliding Performance

FCS-20G combines three key elements:

High-Hardness Pearlitic Matrix

The pearlitic structure increases the surface hardness of FCS-20G to approximately 250–280 HV0.05. As a result, the sliding bearing can:

  • Limit surface deformation
  • Provide better wear resistance
  • Maintain the clearance between the shaft and the bushing for a longer period
  • Be suitable for high surface pressure conditions

Free Graphite for Anti-Seizure Support

Graphite dispersed within the material acts as a solid lubricant. When the lubricating oil cannot form a stable film, graphite helps reduce friction and limit direct contact between the two metal surfaces. This is particularly important during startup, shutdown, or reversal of motion.

Porous Structure for Oil Retention

As a sintered material, FCS-20G has a porous system capable of retaining lubricating oil. During operation, oil is supplied from the pores to the inner diameter surface of the bushing, helping to form a lubricating film between the shaft and the bushing. Microscopic images in the document clearly show the distribution of graphite and pores on the inner surface of the bushing.

What Operating Conditions is FCS-20G Suitable For?

FCS-20G is developed for applications with:

  • Low speed
  • Oscillatory motion
  • High loads
  • High surface pressure
  • Frequent starts and stops
  • Difficulty in maintaining a stable oil film

These conditions often lead to increased wear and the occurrence of カジリ, which refers to scratching, stick-slip, or surface seizure.

Load Parameters and Application Range

ItemValue
Main CompositionFe–C
Permissible PV200 MPa·m/min
Maximum Surface Pressure Pmax4 MPa
Maximum Sliding Speed Vmax100 m/min
Surface Hardness250–280 HV0.05

FCS-20G Material Composition

ComponentContent
FeBalance
Cu1–3 wt%
Sn≤ 2 wt%
C2–4 wt%
Other Components≤ 3 wt%

In addition to its chemical composition, the performance of FCS-20G also depends on its pearlitic structure, graphite distribution, and porous structure.

Typical Applications of FCS-20G

FCS-20G is primarily used for motors operating under high load conditions, including:

  • Automotive seat slide motors
  • Power window motors
  • Automotive sliding door motors
  • Other high-load motors

These mechanisms typically operate at low speeds, with intermittent operation, frequent reversals, and relatively high loads. Therefore, bushings need to have both wear resistance and anti-seizure capabilities.

When to Consider Using FCS-20G?

FCS-20G can be considered when:

  • Shaft bushings experience rapid wear
  • Clearance between the shaft and bushing increases prematurely
  • Bushing surfaces show scratching or seizure
  • Mechanisms operate at low speed but high load
  • Shaft undergoes oscillatory or reversing motion
  • Equipment starts and stops frequently
  • Conventional sliding bearing materials do not meet lifespan requirements

Technical Support from Peace-Lon Vietnam

Peace-Lon Vietnam provides support in selecting oil-impregnated self-lubricating sliding bearing materials based on the actual operating conditions of each product. Based on information regarding load, speed, type of motion, shaft material, roughness, lubricating oil, and required lifespan, Peace-Lon can assist from material selection, trial production, and sliding performance evaluation to mass production. If shaft bushings are experiencing issues with wear, scratching, or seizure under high load conditions, FCS-20G is a material option worth considering.

Company Information

PEACE-LON VIETNAM COMPANY LIMITED

Industry Classification

Electronic parts

Main 3 Products

Oil-impregnated sintered bearing / Gears, pulleys, and other mechanical parts / Powder Metallurgy

Homepage URL

Display URL

Peace-Lon is a brand of Heiwa Sangyo Co., Ltd., a Japanese company that has manufactured self-lubricating oil-impregnated plain bearings and sintered mechanical parts utilizing powder metallurgy and s ...

PICKUP

Technology & Services

CONTACT

Contact

This is the inquiry form for PEACE-LON VIETNAM COMPANY LIMITED. Please enter your inquiry details.

This service is intended for consulting on processing projects and requesting quotes.
Please do not use it for company PR or sales activities.
If we receive complaints about the content sent, we may take measures such as forcibly suspending usage.

Name*Required
Company Name*Required
Department
Position
Email Address*Required
Phone Number*Required
Inquiry Type*Required
Inquiry Content*Required
Attach File

Only files with extensions of images (jpeg, jpg, gif, png, pdf) and compressed files (zip, lzh) are valid. Maximum file size 10MB